Hpe 813874-B21-I Compatible 10gbase-T SFP+ Copper Rj-45 30m Industrial Transceiver Module

• Type: Both Single Mode and Multi Mode
• Transport Package: Blister Pack
• Trademark: Linksall
• Origin: China
• Model NO.: LADX-COPP-ZR
• HS Code: 8517706000
• Production Capacity: 100, 000 Per Year

Product Description

10G Base-T Copper SFP transceiver module
Features

1. Support 10GBASE-T Operation in Host Systems
2. Support RX_LOS as Link indication function
3. Hot-Pluggable SFP Footprint
4. Compact RJ-45 Connector Assembly
5. Compliant with SFP MSA
6. Operating Case Temperature: 0ºC~70ºC

 

Applications

1. 10G BASE-T IEEE 802.3an
2. 1000BASE-T IEEE 802.3ab
3. 100BASE-TX IEEE 802.3u
4. 5G MGBASE-T
5. 2.5G MGBASE-T

 

Product Description

UNSFP-10G-T, 10G BASE-T Copper Small Form Pluggable (SFP) modules are based on the SFP Multi Source Agreement (MSA). It is compliant with the 10G BASE-T, 1000BASE-T, 100BASE-TX standards as specified in IEEE STD 802.3an, 802.3ab and 802.3au.
 

Absolute Maximum Ratings*

Parameter	Symbol	Min	Type	Max	Units
Maximum Supply Voltage	Vcc	-0.5		4.0	V
Storage Temperature	TS	-40		85	°C

*Exceeding any one of these values may destroy the device permanently.
 

Normal operating condition

Parameter	Symbol		Min	Type	Max	Units
Operating Case Temperature	Tc	UNSFP-10G-T	0		70	°C
Supply Voltage	Vcc		3.14	3.3	3.46	V

Regulatory Compliance*Note1

Product Certificate	Certificate Number	Applicable Standard
TUV	R50135086	EN 60950-1:2006+A11+A1+A12+A2
		EN 60825-1:2014
		EN 60825-2:2004+A1+A2
UL	E317337	UL 60950-1
		CSA C22.2 No. 60950-1-07
EMC CE	AE 50285865 0001	EN 55022:2010
		EN 55024:2010
FCC	WTF14F0514417E	47 CFR PART 15 OCT., 2013
FDA	/	CDRH 1040.10
ROHS	/	2011/65/EU

Note1: The above certificate number updated to June 2014, because some certificate will be updated every year, such as FDA and ROHS.
 

Electrical Characteristics

Parameter	Symbol	Min	Typ	Max	Units	Notes/Conditions
+3.3 Volt Electrical Power Interface
Supply Current	Icc			800	mA
Input Voltage	Vcc	3.13	3.3	3.47	V
Low-Speed Signals, Electronic Characteristics
SFP Output LOW	VOL	0		0.5	V	4.7k to 10k pull-up to host_Vcc, measured at host side of connector
SFP Output HIGH	OH	host_ Vcc - 0.5		host_ Vcc + 0.3	V	4.7k to 10k pull-up to host_Vcc, measured at host side of connector
SFP Input LOW	VIL	0		0.8	V	4.7k to 10k pull-up to Vcc, measured at SFP side of connector
SFP Input HIGH	VIH	2		Vcc + 0.3	V	4.7k to 10k pull-up to Vcc, measured at SFP side of connector
High-Speed Electrical Interface, Transmission Line-SFP
Tx Output impedance	Zout,TX		100		Ohm	Differential, for all frequencies between 1MHz and 125MHz
Rx Input Impedance	Zin,RX		100		Ohm	Differential, for all frequencies between 1MHz and 125MHz
High-Speed Electrical Interface, Host-SFP
Single ended data input swing	Vin	250		1200	mV	Single ended
Single ended data output swing	Vout	350		800	mV	Single ended
Rise/Fall Time	Tr,Tf		20		psec	20%-80%
Tx Input Impedance	Zin		50		Ohm	Single ended
Rx Output Impedance	Zout		50		Ohm	Single ended

 

Pin Descriptions

Pin No.	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter Ground	1
2	TX Fault	Transmitter Fault Indication	3	Not used
3	TX Disable	Transmitter Disable	3	1
4	MOD-DEF2	Module Definition 2	3	2
5	MOD-DEF1	Module Definition 1	3	2
6	MOD-DEF0	Module Definition 0	3	2
7	RS0	No Connection required	3
8	LOS	Loss of Signal	3	RX_LOSS
9	RS1	No Connection required	1
10	VeeR	Receiver Ground	1
11	VeeR	Receiver Ground	1
12	RD-	Inv. Received Data Out	3
13	RD+	Received Data Out	3
14	VeeR	Receiver Ground	1
15	VccR	Receiver Power	2
16	VccT	Transmitter Power	2
17	VeeT	Transmitter Ground	1
18	TD+	Transmit Data In	3
19	TD-	Inv. Transmit Data In	3
20	VeeT	Transmitter Ground	1

Notes:   

1. PHY disabled on TDIS > 2.0V or open, enabled on TDIS < 0.8V, used to reset the module.
2. Should be pulled up with 4.7k - 10k Ohm on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF(0) pulls line low to indicate module is plugged in.Serial Communication Protocol

UNSFP-10G-T support the 2-wire serial communication protocol outlined in the SFP MSA, These SFP use a 128 byte EEPROM with an address of A0H.
 

EEPROM Serial ID Memory Contents

Accessing Serial ID Memory uses the 2 wire address 1010000X (A0H). Memory Contents of Serial ID are shown in Table 1.

Table 1 Serial ID Memory Contents

Addr.	Size (Bytes)		Name of Field	Hex		Description
BASE ID FIELDS
0	1		Identifier	03		SFP
1	1		Ext. Identifier	04		SFP function is defined by serial ID only
2		1	Connector	07		-LC
3-10		8	Transceiver	10 00 00 00 00 00 00 00		Transmitter Code
11		1	Encoding	06		64B/66B
12		1	BR, Nominal	67		10.3G
13		1	Reserved	00		-
14		1	Length (9µm)km	00
15		1	Length(9µm)100m	00
16		1	Length (50µm) 10m	08		80m
17		1	Length(62.5µm)10m	02		20m
18		1	Length (Copper)	00
19		1	Reserved	1E		300m
20-35		16	Vendor name	XX XX XX XX XX XX XX XX(note2)20 20 20 20 20 20 20 20		Vendor name (ASCII)
36		1	Reserved	00		-
37-39		3	Vendor OUI	XX XX XX(note2)		-
40-55		16	Vendor PN	XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX(note2)		Transceiver part number
56-59		4	Vendor rev	XX XX XX XX(note2)		-
60-61		2	Wavelength	03 52		-850nm
62		1	Reserved	00		-
63		1	CC_BASE	Check Sum (Variable)		Check code for Base ID Fields
EXTENDED ID FIELDS
64-65		2	Options		00 1A		TX_DISABLE, TX_FAULT and Loss of Signal implemented.
66		1	BR, max		00
67		1	BR, min		00
68-83		16	Vendor SN		XX XX XX XX XX XX XX XX 20 20 20 20 20 20 20 20(note2)		Serial Number of transceiver (ASCII). For example "B000822".
84-91		8	Date code		XX XX XX XX XX XX XX XX(note2)		Manufactory date code. For example "080405".
92		1	Diagnostic Monitoring Type		XX(note2)		Digital diagnostic monitoring implemented
93		1	Enhanced Options		XX(note2)		Optional flags
94		1	SFF_8472 Compliance		XX(note2)		01 for diagnostics (Rev9.3 SFF-8472).
95		1	CC_EXT		Check Sum		Check sum for Extended ID
					(Variable)		Field.
VENDOR SPECIFIC ID FIELDS
96-127	32		Vendor Specific		Read only		Depends on customer information
128-255	128		Reserved		Read only		-

Note2: The "XX" byte should be filled in according to practical case. For more information, please refer to the related document of SFP Multi-Source Agreement (MSA).

Order Information

Part No.	Data Rate	Media type	Distance	Connector	Temperature
UNSFP-10G-T* Note3	10G	CAT6A/CAT7	30m	RJ45	Standard

Note3: Standard version.
*The product image only for reference purpose.